- This line was added.
- This line was removed.
- Formatting was changed.
Effectors are a special type group of Modifiers which are used by by the Motion: Physics feature. They apply non-uniform forces to particles and are used to add flair to an otherwise standard physical motion.
For more information about particle physics, refer to the Motion section.
Effectors can be found under Local Effectors dropdown menu and it includes the following options:
Modifiers and Effectors can be combined to create highly sophisticated effects.
Turbulence simulates the motion of particles within a participating medium like air or water. Although participating mediums might be invisible in games, simulating their turbulence allows for the creation of complex and convincing effects
This effector creates the impression that particles are floating in a medium rather than appearing to be in a vacuum. The Turbulence Effector is applied in world space and does not depend on parent location.
For more information about parent child relationships, see Child.
Specifies the type of turbulence to be simulated:
Specifies how fast the turbulence is applied to the particles. The actual behavior will depend on the Mode.
Only used by Simplex or Simplex Curl. Turbulence uses Simplex noise to generate a vector field, which is similar to Perlin noise, but can be more efficient in some cases. This type of noise creates a uniform grid of vertices in space and sets a random value to each vertex. The actual velocity applied to the particle is interpolated from this grid. Size therefore specifies the distance between these vertices in this grid. If size is too small, turbulence will start to get more random, fuzzy and diffuse. If size is too large, particles will start moving mostly in the same direction and no interesting shapes will arise.
Only used by Simplex or Simplex Curl. One of the main advantages of Simplex noise is that it is relatively efficient to not just generate a smooth noise in space, but those that can also smoothly evolve over time. Rate controls how fast this evolution occurs. A value of 0 means no evolution and particles will always travel over the same routes.
Only used by Simplex or Simplex Curl. Adds additional complexity by sampling the noise field multiple times with different sizes. This option enables the creation of Fractal Noise.
Allows non-uniform scaling of the turbulence.
Gravity applies a gravitational force to all particles relative to a point in space. While global gravity is a uniform force, this option is non-uniform.
Gravity does not require Drag and it only affects the acceleration. In fact, higher amounts of drag will reduce the gravity effect. Also, Gravity's Scale does not scale this effect, it is only scaled by global gravity.
Specifies the source of gravity for each particle:
Offsets source of the gravity field in space.
Shapes the gravity field:
Maximum amount of acceleration to be applied to the particles in meters per second squared (m/s2). If this value is negative, particles are rejected instead of being attracted to the target.
Acceleration is not uniformly applied to all particles, it decays with the distance to the target. Decay corresponds to the distance, in meters, at which acceleration is halved.
Valid only when Cylindrical type is selected. Specifies the direction of the axis in the parent's space.
Vortex simulates the effect of turbulent wind.
The Vortex Effector affects wind velocity and requires the Drag option. The higher the drag value, the faster the particles snap to the vortex.
Specifies where the center of the vortex should appear:
Offsets the center of the vortex in space.
Maximum speed of the wind formed by the vortex. The speed value is calculated in meters per second.
Wind velocity is not uniformly applied to all particles, it decays with the distance to the target. Decay corresponds to the distance, in meters, at which the acceleration is reduced by half. Decay follows the inverse squared law.
Direction the wind should flow; clockwise or counterclockwise.
Specified direction of the vortex axis in parent's space.
Makes particles move in a spiral motion based on their velocity. Can be used to create certain special types of turbulence motion effects.
Specifies the size for the spiral.
Specifies the velocity for the particles around the spiral.
All Effectors are supported by the GPU pipeline. There are some limitations to be taken into account though, this is due to the way the GPU system processes particles;
- There can only be one Effector of each type active at the same time
- The order in which the Effectors are stacked and executed is always:
- Brownian - Turbulence
- Simplex - Turbulence
- Simplex Curl - Turbulence
On This Page
|Table of Contents|