Depending upon the situation CryAnimation uses different units of 'time'. How those units of time compare is best explained using an example.
First off a definition of 'frames' - CryAnimation uses a fixed rate of 30 Frames per Second (fps). Of course games can run at higher frame rates, but some operations in the Editor that use the concept of 'frames' or operations that clamp the animation duration to 'one frame' assume a frame rate of 30 fps.
Let's say then, that we have an animation with a duration of 1.5 seconds. This means the animation has 46 frames (note this includes the final frame). so, in the case of Real Time we can assume an animation starts at time 0, has no segmentation and is played back at normal speed. However, rather than using Real Time, CryAnimation typically uses Animation Normalized Time - this is compared with Real Time in the table below:
|Frame Index||Real Time|
Animation Normalized Time
|1||0.033.. s = 1/30 s||0.022.. = 1/45|
|30||1.0 s||0.666.. = 30/45|
|44||1.466.. s = 44/30 s||0.977.. = 44/45|
|45||1.5 s = 45/30 s||1.0|
Real Time is used to define Duration
IAnimationSet::GetDuration_sec()returns the duration of an animation. Note: for a parametric animation this returns only a crude approximation: the average duration of all its examples, ignoring parameters or speed scaling
CAnimation::GetExpectedTotalDurationSeconds()returns the duration of an animation that is currently playing back. Note: for a parametric animation this returns only a crude approximation, assuming the parameters are the ones that are currently set and never change throughout the animation
In practice CryAnimation doesn't really use Animation Normalized Time (this terminology has been used to make the introduction easier to understand), typically it uses Segment Normalized Time and for this you need to understand Segmentation.
For time warping (phase matching) purposes animations can be split into multiple segments, for example you want to time warp from a walk animation with 2 cycles to a walk animation with 1 cycle. In this case you have to annotate the first animation and split it into two - this is what we mean by Segments. This segmentation is achieved by adding a segment1 animevent at the border between the cycles.
Note: an animation without segmentation has exactly 1 segment which runs from beginning to end.
Segmentation introduces a new unit for time, Segment Normalized Time which is time relative to the current segment duration.
So, extending our example, see how the table now looks when a segment1 animevent at 1.0s has been added to split the animation into two segments.
|Frame Index||Real Time||AnimEvents||(Animation) Normalized Time||Segment Index||Segment Normalized Time|
|1||0.033.. s||0.022..||0||0.033.. = 1/30|
|44||1.466.. s||0.977..||1||0.933.. = 14/15|
CAnimation::GetCurrentSegmentIndex()to retrieve it
CAnimation::Get/SetCurrentSegmentNormalizedTime()to get/set the Segment Normalized Time
CAnimation::GetCurrentSegmentIndex()retrieves the current segment index and
CAnimation::GetCurrentSegmentExpectedDurationSeconds() retrieves the duration of the current segment
Playback speed does not impact the functions that compute duration of playing animations such as
Animation Normalized Time, Segment Index and Duration all create ambiguity for segmented parametric animations. This is because each example animation within the parametric animation can have its own number of segments, this complicates matters.
So to avoid ambiguity, Animevents in/on segmented parametric animations use Segment Normalized Time. Note: because of this an Animevent will be fired multiple times (once per segment) during the animation
ISkeletonAnim::GetAnimationNormalizedTime() uses a heuristic: it currently looks for the example animation with the largest number of segments and returns the animation normalized time within that example.
ISkeletonAnim::GetCurrentSegmentIndex() uses a different heuristic: it currently returns the segment index in the example animation which happens to be the first in the list.
Given this we are considering redefining the above based on the following observation;
You can define the total number of segments in a parametric animation as the number of segments until repetition starts.
So, let's say you have a parametric animation consisting of 2 examples, one with 2 segments and the other with 3 segments. This will start to repeat after 6 segments (the lowest common multiple of 2 and 3). However, you can uniquely identify each possible combination of segments using any number from 0 to 5.
This method is used in the Character Tool to achieve a well defined duration. For this we implemented;
ISkeletonAnim::CalculateCompleteBlendSpaceDuration(). This function calculates the duration until the parametric animation starts to repeat (assuming the parameters remain fixed). It reverts to the regular
GetExpectedTotalDurationSeconds() implementation for non-parametric animations so the function can be used in more general situations.
Normally your animations have at least two keys. However, when you convert these into additive animations the first frame is interpreted as the base from which to calculate the additive, hence this leaves only 1 frame in the additive animation (currently this means that in respect to the asset both the start and end time of the asset are set to 1/30 s)
Functions retrieving the total duration of this animation will return 0.0. (e.g.
However, for playback purposes CryAnimation will handle these animations as if they have a duration of 1/30th of a second. For e.g. Animation Normalized Time will still progress from 0 to 1 while the time goes from 0 to 1/30th of a second.
CAnimation::GetCurrentSegmentExpectedDurationSecond() will also return 1/30th of a second in this case.
Time typically cannot run backwards when playing an animation.
You can only move time backwards if you do it manually. This can be achieved by setting the flag CA_MANUAL_UPDATE on the animation and using
CAnimation::SetCurrentSegmentNormalizedTime - see the example
This section is only relevant to full source code Licensees.
For the controllers that contain the actual key data and that are used for animation sampling then different units are used.
|Frame Index||Real Time||I_CAF Ticks||Keytime|
Animation assets can also have a StartTime other than 0.0s - this complicates matters a little, but only for the controllers. Typically, everywhere but the controllers, time is taken relative to this StartTime.